Triumph Daytona 675 Specs
Introduced in 2006, the Daytona 675 is a middleweight sport bike built by Triumph Motorcycles to replace the Daytona 650. The following technical specification applies for Triumph Daytona 675 models. Here you will find detail information about the engine, dimension, transmission, frame and electrical system specifications of Daytona 675 motorcycle. (Source: Daytona 675 Service Manual).
ENGINE
| Type | 3-cylinder 12 valve DOHC |
| Arrangement | Transverse in-line |
| Displacement | 674.8 cc |
| Bore x stroke | 74 x 52.3 mm |
| Compression ratio | 12.65 : 1 |
| Cylinder numbering | Left to right (no.3 adjacent to camchain) |
| Cylinder sequence | Number 1 at left |
| Firing order | 1 – 2 – 3 |
| Max. Power | 125 PS (123 bhp) @12,500 rpm |
| Max. Torque | 72 Nm (53.3 ft.lbf) @11,750 rpm |
CYLINDER HEAD
| Valve head diameter | In. : 30.50 mm Ex. : 25.50 mm |
| Valve lift | In. : 9.25 mm Ex. : 8.50 mm |
| Valve timing: Inlet open Inlet close Duration Exhaust open Exhaust close Duration |
. 27.25º BTDC @1.0 mm lift 51.25º ABDC @1.0 mm lift 258.50º 43.00º BBDC @1.0 mm lift 23.00º ATDC @1.0 mm lift 246º |
CLUTCH
| Primary drive type | Gear |
| Primary reduction ratio | 1.848 (46/85) |
| Clutch type | Wet multi plate |
| No. of friction plates | 9 |
| Clutch actuation method | Cable |
| Cable free play (at lever) | 2 – 3 mm |
TRANSMISSION
| Type | 6 speed constant mesh |
| Gear ratios: 1st 2nd 3rd 4th 5th 6th |
2.615 (34/13) 1.857 (39/21) 1.565 (36/23) 1.350 (27/20) 1.238 (26/21) 1.136 (25/22) |
| Gear selector fork thickness | 5.9 mm – 6.0 mm (5.8 mm min) |
| Gear selector groove width | 6.1 mm – 6.17 mm (6.27 mm max) |
| Gear selector fork to groove clearance | 0.47 mm max |
| Final drive type | Chain |
| Final drive ratio | 2.937 (16/47) |
| Chain type | RK O-ring |
| No. of links | 106 links |
| Drive chain play | 35 – 40 mm |
| Chain lubrication | Mobile chain spray |
LUBRICATION
| Type | Pressure lubrication, wet sump |
| Oil capacity (incl filter dry fill) | 3.0 litres |
| Oil and filter change | 2.6 litres |
| Oil change only | 2.4 litres |
| Oil pressure (in main gallery) | 30.0 lb/in² @5,000 rpm (@80 ºC Oil temp.) |
| Oil pump rotor tip clearance | 0.15 mm (0.20 mm max) |
| Oil pump body clearance | 0.15 mm – 0.22 mm (0.35 mm max) |
| Oil pump rotor end float | 0.04 mm – 0.09 mm (0.17 mm max) |
IGNITION SYSTEM
| Type | Digital inductive |
| Electronic Rev-limiter | 14,000 rpm |
| Pick up coil resistance | 0.21 Kohm ± 10% @20 ºC |
| Ignition coil type | Plug top |
| Spark plug type | NGK CR9EK |
| Spark plug gap | 0.7 mm |
FUEL SYSTEM
| Fuel type | Unleaded 95 RON |
| Fuel tank capacity | 17.4 litres |
| Fuel level warning lamp | 4 litres remaining |
| Purge control system | Electronic via fuel system ECU |
| Fuel injection system | Electronic, sequential |
| Idle speed | 1,200 rpm |
| Injector type | Twin jet, solenoid operated plate valve |
COOLING SYSTEM
| Coolant mixture | 50/50 distilled water/ anti-freeze |
| Anti-freeze type | Mobil antifreeze |
| Freezing point | -35 ºC |
| Cooling system capacity | 2.4 litres |
| Radiator cap opening pressure | 1.1 bar |
| Thermostat opening temperature | 71 ºC |
| Cooling fan switch on temperature | 103 ºC |
| Temperature gauge sensor resistance | 2.9 – 3.3 Kohm @15ºC |
SUSPENSION
| Front fork travel | 110 mm |
| Recommended fork oil grade | Kayaba KHL15-10 |
| Oil level (fork fully compressed) | 72 mm |
| Oil volume (dry fill) | 495 cc |
| Front fork pull through | 4 mm |
| Rear travel wheel | 130 mm |
| Rear suspension bearing grease | Mobil grease HP 222 |
BRAKES
| Front type | Two hydraulically actuated four piston calipers action on twin discs |
| Caliper piston diameter | 33.96 mm/30.23 mm |
| Disc diameter | 308 mm |
| Disc thickness | 5 mm |
| Recommended fluid | Mobil universal brake and clutch fluid DOT 4 |
| Rear type | Hydraucally actuated single piston caliper, single dics |
| Caliper piston diameter | 38.18 mm |
| Disc diameter | 220 mm |
| Disc thickness | 5 mm |
| Recommended fluid | Mobil universal brake and clutch fluid DOT 4 |
WHEEL and TIRES
| Front wheel size | MT 3.5 x 17 |
| Front tire size | 120/70 ZR 17 |
| Front tire pressure | 2.35 bar |
| Front wheel rim axial run-out | 0.5 mm |
| Front wheel rim radial run-out | 0.5 mm |
| Rear wheel size | MT 5.5 x 17 |
| Rear tire size | 180/55 ZR 17 |
| Rear tire pressure | 2.5 bar |
| Rear wheel rim axial run-out | 0.5 mm |
| Rear wheel rim radial run-out | 0.5 mm |
FRAME
| Type | Twin-spar aluminum |
| Overall length | 2,110 mm |
| Overall width | 700 mm |
| Overall height | 1,120 mm |
| Wheelbase | 1,395 mm |
| Seat height | 825 mm |
| Castor | 23.9º |
| Trail | 89.1 mm |
| Dry weight | 165 kg |
ELECTRICAL
| Battery type | YT 7B – BS |
| Battery rating | 12V – 6.5 Amp hour |
| Alternator rating | 33.5 A @4,000 rpm |
Related Posts:
Tags: Engine, Frame, Gearbox, Suspension, Tire, Transmission, Wheel